Titanium Guide

2021-09-16 Titanium Guide Comments Off on Best brazing method for titanium and its alloys

Titanium alloys are active metals and are widely used in aerospace, petrochemical and atomic energy industries. The main problems in titanium and titanium alloy brazing are as follows: (1)The oxide fi...

2021-09-16 Titanium Guide Comments Off on Effect of β treatment on properties of TC4 sheet

Ti-6al-4v alloy has 6% aluminum and 4% vanadium, which is the largest in both domestic and foreign countries. In recent years, some major developed countries have also imported this titanium alloy pla...

2021-09-15 Titanium Guide Comments Off on Research progress on the effect of surface modification of titanium implants on macrophage polarization

At present, inert metal titanium implants are widely used in clinic. However, a 19-year retrospective study showed that about 47 percent of early implant failure was due to poor post-implant inflammat...

2021-09-15 Titanium Guide Comments Off on Analysis on deformation characteristics of die forging technology of titanium bar

Titanium bar blank products process die forgings arrangement and functional uniformity stainless steel forgings. After recrystallization heat treatment, the low-power and high-power equiaxed fine crys...

2021-09-15 Titanium Guide Comments Off on Production process of traditional titanium bar technology

The traditional process of titanium bar is to cast spongy titanium into ingot, and then produce the bar by forging and rolling. Spongy titanium is the most primitive material for producing titanium. W...

2021-09-15 Titanium Guide Comments Off on Effect of Industrial Substance Conventional Elements on the Function of Titanium bar

Titanium bars exist in two shapes, one is free carbon (graphite), mainly in cast green titanium, and the other is compound carbon (titanium carbide), mainly in steel making titanium. Titanium carbide ...

2021-09-14 Titanium Guide Comments Off on GR5 titanium bar, titanium alloy bar polishing technology introduction

1. Grind flat, use 320grit sandpaper for water cooling, grind for 2 ~ 3 minutes, remove the damage layer caused by cutting, and make the surface of the sample flat. Use 320grit SiC sandpaper, water-co...

2021-09-14 Titanium Guide Comments Off on Research on Forging Process of BT22 Large Bar

BT22 titanium alloy bar has a nominal composition of Ti-5Al-5Mo-5V-1Cr-1Fe, which is a high-strength and high-toughness titanium alloy. The outstanding advantage of the alloy is that it has a very hig...

2021-09-14 Titanium Guide Comments Off on Polishing methods and techniques of titanium bars and titanium alloys

Polishing method of titanium bar and titanium alloy: (1) Fine grinding That is, the surface of titanium and titanium alloy castings is ground by using various types of corundum rubber wheels. The prob...

2021-09-14 Titanium Guide Comments Off on Effect of Industrial Substance Conventional Elements on the Function of Titanium bar

Titanium bars exist in two shapes, one is free carbon (graphite), mainly in cast green titanium, and the other is compound carbon (titanium carbide), mainly in steel making titanium. Titanium carbide ...

2021-09-13 Titanium Guide Comments Off on Applications of Titanium bars

Medical titanium bar is an important branch of materials science. It is a new carrier material with high technological content and high economic value for diagnosis, treatment or replacement of human ...

2021-09-13 Titanium Guide Comments Off on Application of titanium bars and titanium materials in the field of information technology

Titanium bars and titanium alloys are an important part of modern materials in the energy, information technology and materials of the three pillars of contemporary civilization. They have a close rel...

2021-09-13 Titanium Guide Comments Off on The effect of industrial substantial convention elements on the function of titanium rod

In titanium rod exist in two shapes, one is free of carbon (graphite), primary exists in casting titanium, the other is a compound carbon (titanium carbide), primary exists in steelmaking raw titanium...

2021-09-13 Titanium Guide Comments Off on Development of titanium bar straightness and diameter composite measuring instrument

The straightness of the titanium bar is measured by a two-dimensional laser measurement sensor. The two-dimensional laser measurement sensor is a high-precision sensor that can simultaneously measure ...

2021-09-12 Titanium Guide Comments Off on Dimension specification for titanium rod, plate, tube and wire

The dimension of titanium material is one of the basic knowledge of titanium material, the dimension of titanium material generally refers to the length of titanium material, the length of titanium ma...

2021-09-12 Titanium Guide Comments Off on Effect of In-Plane Anisotropy and Surface Anisotropy on Titanium Plate Formability

1.Influence of in-plane heterogeneity on sheet formability Different performances in different directions with respect to the rolling direction of the titanium plate, so that the deformation of the cy...

2021-09-12 Titanium Guide Comments Off on What are the actual storage requirements for titanium bars and wires?

Titanium alloy bar and wire have the characteristics of small specific gravity, high thermal strength, thermal stability and good corrosion resistance, which are widely used in aviation, aerospace, at...

2021-09-12 Titanium Guide Comments Off on Characteristics of titanium alloy materials such as titanium bar and titanium alloy bar and categories of heat treatment technology of the rod

TC11 titanium alloy bar is a kind of alpha + beta heat-resisting titanium alloy, which is mainly used for manufacturing compressor disc, blade and other parts of aircraft. It is the main titanium allo...

2021-09-11 Titanium Guide Comments Off on Process knowhow for processing titanium alloy bar

On the basis of understanding the processing mechanism of titanium alloy bar and previous experience, the main process tips for processing titanium alloy bar are as follows: (1) Positive Angle geometr...

2021-09-11 Titanium Guide Comments Off on Physical phenomena when titanium bar processing

The cutting force of titanium alloy bar is only slightly higher than that of steel of the same hardness. Why do we think titanium alloy is a difficult material to process? Because of the lack of under...

2021-09-11 Titanium Guide Comments Off on Classification and development of titanium wires

Titanium and titanium alloy wire as an important variety of titanium material series, no matter from the output, specifications and application of the present has been a considerable development. Gene...

2021-09-11 Titanium Guide Comments Off on Methods and techniques for polishing titanium bar and titanium alloy

Polishing methods of titanium bar and titanium alloy: (1) fine grinding In other words, the surface of titanium and titanium alloy castings is ground by using various kinds of emery rubber wheels. Whe...

2021-09-10 Titanium Guide Comments Off on Eliminate defects in titanium screw manufacturing process

Titanium screws will not only absorb and react strongly with 02, N2, H2, CO, CO2, H2O and NH3 in the ambient atmosphere in the melting state, but also act with most of the known crucible materials. Th...

2021-09-10 Titanium Guide Comments Off on A feasible method to identify fake titanium bar products

Titanium bar acquisition, want to buy high-quality titanium bar, but how to identify the good or bad titanium bar? Titanium alloy from many aspects, multi – Angle to identify the quality of tita...

2021-09-10 Titanium Guide Comments Off on Why is the comprehensive property of titanium bar so strong?

Titanium bar is a kind of special metal, it is small in density and light in weight, but very high in strength, and strong in corrosion resistance, it will not be black like silver, at room temperatur...

2021-09-10 Titanium Guide Comments Off on Metallurgical engineering alloying of titanium liquid in the process of making titanium rod

The operation of adjusting the composition of liquid titanium alloy in the process of making titanium rod is called alloying. The alloying of titanium rod made by traditional electric furnace in metal...

2021-09-09 Titanium Guide Comments Off on Titanium plate thermal alignment meet the requirements

The proper heating temperature, holding time and forming pressure must be selected for the forming work of titanium plate. Heat alignment on the parts of the pressure, as long as you can ensure that t...

2021-09-09 Titanium Guide Comments Off on Titanium and titanium alloy plate welding and wire selection

The material characteristics and weldability of titanium and titanium alloy plate, and the weldability tests were carried out for the welding defects of titanium and titanium alloy which are easy to p...

2021-09-09 Titanium Guide Comments Off on Processing conditions of titanium alloy tubes

In the process of titanium tube, in order to check whether the materials mixed by the shaft air separation method are evenly distributed in the boiling layer and whether there is stratification or seg...

2021-09-09 Titanium Guide Comments Off on Titanium plate and titanium alloy plate straightening method

There are many straightening methods for metals, and most of them are currently mechanical straightening. Commonly used methods are pressure straightening, roll straightening and tension straightening...

2021-09-08 Titanium Guide Comments Off on Application of titanium wire and titanium alloy wire

Titanium and titanium alloy as metal materials, with many other metal materials incomparable excellent performance, widely used in a variety of industrial and civil consumer goods. 1. Classification o...

2021-09-08 Titanium Guide Comments Off on Titanium plate blanking and forming cleaning

Titanium plate blank blanking There are many similarities in the preparation methods of wool used in various sheet metal parts. Due to the use of titanium plate thickness is generally below 2 mm, and ...

2021-09-08 Titanium Guide Comments Off on ​Preparation of titanium plate for raw material supply status requirements

Titanium is a very active metal element that can interact with all elements. When heated, titanium can interact with oxygen to form an oxide film on its surface. The structure and properties of oxide ...

2021-09-08 Titanium Guide Comments Off on MIT is developing a supercapacitor made of niobium wire

The breakthrough is said to be a new way to make ultracapacitors using niobium wires – nanowires made of niobium – which are used in the electrodes of ultracapacitors. This gives ultracapa...

2021-09-07 Titanium Guide Comments Off on Production of titanium screws

Titanium screw, when we use the place of screw in life is really a lot of, but the understanding of titanium alloy screw is the hard truth, or choose to poor quality products on the reaction. So when ...

2021-09-07 Titanium Guide Comments Off on Effect of annealing temperature on microstructure and properties of titanium target

As the annealing temperature increased from 650 ℃ to 800 ℃, the tensile strength and specified non-proportional extension strength of titanium target decreased gradually, and the elongation increased ...